The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
Presented here down the page you can get more sound ideas relating to How to Install a Bathtub.
Mounting a tub isn't exactly rocket science, however it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open up a wall surface to remove the old tub and place the brand-new tub, the task is much harder. In either situation, the job is within a home handyman's skills, although you will need a helper to leave the old tub and embeded in the new one. See to it you have certified on your own for the job and also fit attempting it. As opposed to employing a specialist to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This write-up will assist you install a brand-new bath tub in your shower room if you have actually currently acquired a new bathtub as well as don't need to transform the arrangement of your previous supply of water pipes.
Your devices as well as product checklist should consist of the following:
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will come from the pipelines. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the outermost versatile faucet connector to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Activate the water as well as check all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as also inspect the overflow outlet as well as the typical outlet for leaks.
Finally, repair the bath paneling as described in the producer's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has been used at least when as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet ends first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes and also cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the market. It is a good idea to fit the tiles using water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that write-up about How to Install a Bathtub from a friend on a different web blog. Enjoyed reading our review? Please share it. Let other people discover it. I praise you for your time. Come back soon.
Further Details Report this page